How to measure lux: a reliable method with a lux meter or a phone app
To measure lux, hold a lux meter or phone flat at the surface you care about, sensor facing the light, after the lamps have been on five minutes. Step out of its shadow, wait for the number to settle, take four readings across the area and average them. On a phone, white paper over the camera steadies the reading.
Is your desk at 150 lux or 500? Is the corner by the window bright enough for a plant? Does your light box really give 10,000? A lux reading answers all three, but only if you take it the right way. Hold the sensor at the wrong angle or stand in your own shadow and the number can be off by half. Here is the method professionals use, adapted for a phone.
Lux meter or phone?
| Handheld lux meter | Phone app | |
|---|---|---|
| What it reads | Light on a flat sensor under a white dome | Light through the camera or the screen's light sensor |
| Typical accuracy | Within a few percent if calibrated | Tens of percent off out of the box; within about 10 to 20 percent with paper and a correction |
| Best for | Workplace compliance, reports, grow tents at scale | Homes, desks, plant spots, light boxes, comparing places |
| Always with you | No | Yes |
The research is clear on both sides. An official guide from the Swedish Work Environment Authority found that without a diffuser, phone values were "more than 3 to 4 times" off; with a sheet of printer paper over the camera and a calibration, all errors stayed under 20 percent and the average under 10. A 2022 study of ten phones found errors from a few percent to about 100 percent, and five different apps on the same iPhone read anywhere from 136 to 400 lux under a 400 lux lamp. The same study found that each phone's error stayed nearly constant under one lamp, so a single correction factor fixes most of it.
The practical takeaway: a phone is a good lux meter for home decisions once you use paper and correct it once. For a legal workplace survey, use a calibrated meter. How far phones drift and why is covered in detail in is a phone light meter accurate?.
Step by step: how to measure lux
1. Pick the plane that answers your question
| Question | Where to measure | Sensor faces |
|---|---|---|
| Is my desk bright enough? | On the desk top | Up |
| Is the room lit well? | 76 cm (30 in) above the floor, several points | Up |
| Is the hallway or stair safe? | On the floor or the treads | Up |
| How much light reaches my eyes (sleep, light box)? | At eye level | Toward the room or lamp |
| How much light reaches a plant? | At the top leaves | Toward the window or lamp |
The first two are what workplace standards use: CCOHS measures general light 76 cm above the floor, and Canada's federal procedure uses about 1 metre. Body-clock targets are always measured at the eye. Plant light is measured at the leaves; measuring plant light with your phone covers that case.
2. Warm up the lights
Turn the lamps on and wait five minutes. Some bulbs start dimmer and climb. To measure daylight indoors, switch the electric lights off; to measure the lamps, measure after dark or close the blinds.
3. Add a diffuser on a phone
Cover the camera with a single sheet of ordinary white printer paper, held flat, without pressing on the lens. The paper does what the white dome on a real lux meter does: it collects light from every direction, the way a surface receives it. Without it, the camera sees only what it points at and the number swings as you tilt.
For a desk or room check, either camera works. The Swedish authority uses the rear camera with the phone laid screen down; the front camera with the screen up lets you read the number without moving the phone. Pick one and keep it. For a light box, hold the phone at your eyes with the camera facing the lamp.
4. Get out of the way
Your head and body block light. Lay the phone or meter down, step back, and read from the side. If you must hold it, stretch your arm out and keep your body behind the sensor's line to the light.
5. Let the number settle
Wait two or three seconds, then take three readings and keep the middle one. Phone camera readings can jump at very low levels; near 10 lux, steps of up to half the value are normal, so read dim rooms as a range.
6. Take four points, not one
One spot tells you about one spot. Canada's federal procedure takes four readings at representative points and averages them, and warns against picking only the brightest or darkest corners. CCOHS adds a uniformity check: the lowest reading should be at least two-thirds of the average. A room averaging 300 lux with one corner at 120 has a dark corner to fix.
7. Write it down
Date, time, spot, height, which lights were on, and the weather if daylight is involved. A reading without its conditions is hard to compare next week.
Calibrate your phone in two minutes
A correction factor turns a consistent phone into an accurate one.
- Find a known value. Best: borrow a calibrated lux meter. Next best: a light therapy lamp at the exact distance where its maker states 10,000 lux.
- Measure both at the same spot, same height, same lamp, paper on the phone.
- Divide: factor = true value ÷ phone reading. If the meter says 500 and the phone says 400, the factor is 1.25.
- Apply it: multiply future readings by 1.25.
Three rules keep the factor honest. Redo it for each type of light, since the error under a warm LED differs from the error in daylight. Keep one camera, because front and rear cameras often read differently. And check it again after a major phone update.
When you do not need calibration at all
Many questions are comparisons, and comparisons survive a phone's error. Same phone, same method, same camera:
- Which side of the room is brighter?
- Did the new bulb add light at the desk, and how much?
- How much does the light fall from the window to the sofa?
- Does the lamp give its 10,000 lux at your chair, compared with its rated distance?
If the reading doubles, the light doubled, whatever the absolute error. The 10,000 lux light guide uses exactly this ratio method to check a light box with any phone.
Common mistakes
- Pointing the camera at the lamp for a desk reading. The desk receives light from every direction, so measure on the desk, facing up, through paper.
- Measuring right after switching on. Wait five minutes.
- One reading only. Light varies across a room by a factor of three or more.
- Mixing daylight and lamps when you want to judge the lamps.
- Standing over the sensor. Your shadow can cut the reading in half.
What to compare your reading with
Once you have a number, the targets are on their own pages: lux levels by room for desks, kitchens, stairs and offices, how dark your bedroom should be for evenings and nights, and the lux and foot-candle converter if your guide uses the other unit.
Questions people ask
Can my phone measure lux?
Yes, as a good estimate. A lux meter app reads light through the camera or the phone's light sensor. With white paper over the camera and one correction against a known reference, an official Swedish test kept errors under 20 percent. For legal workplace checks, use a calibrated meter.
What app can I use to measure light levels?
Any lux meter app that shows a live reading in lux or foot-candles works for home use. Pick one that lets you choose the front or rear camera and tap a point to meter. Then follow the same method every time, because a consistent method matters more than the app.
Is a lux meter the same as a light meter?
Not quite. A lux meter measures illuminance, the light landing on a surface, in lux or foot-candles. A photographic light meter turns light into exposure settings: aperture, shutter speed and ISO. Many meters and apps do both, since exposure value and lux are linked by a fixed formula.
Where should I hold the meter to measure lux?
At the surface you care about, flat and facing up: on the desk, on the counter, or 76 cm above the floor for general room light. For sleep and body-clock checks, hold it upright at eye level instead, facing the room, because that is the light entering your eyes.
How do I calibrate a phone lux meter?
Put the phone and a calibrated meter at the same spot under the same lamp and divide the meter's reading by the phone's. That ratio is your correction factor; multiply future readings by it. No meter? Use a light therapy lamp at its rated distance as the known value. Redo it for each type of bulb.
Sources
- Swedish Work Environment Authority: Measure light with your mobile Paper over the camera, phone screen down on the surface, light on 5 minutes first; without paper values are more than 3 to 4 times off, with paper and calibration errors stayed under 20 percent.
- Government of Canada (ESDC), Interpretation 039: Lux measurement procedure Four representative readings averaged, sensor facing up about 1 m above the floor, never only the brightest or darkest spots.
- CCOHS: Lighting ergonomics, survey and solutions General lighting measured 76 cm above the floor; the lowest reading should be at least two-thirds of the average.
- Vujica Herzog et al. 2022, DAAAM Scientific Book: Lux meter apps vs illumination measuring devices Ten phones against a reference meter: errors from a few percent to about 100 percent, nearly constant per phone under one lamp, so one correction factor works; five apps on one iPhone read 136 to 400 lux at 400.
- DIAL: Luxmeter app vs measuring device Lab test of older phones: errors up to 113 percent, front and rear cameras often gave different values, single-point calibration failed away from its level.
- Odenwald 2020, Citizen Science: Theory and Practice: Smartphone sensors for light and sound After calibration, camera-based readings stayed within about 12 to 18 percent; readings jump by up to half near 10 lux.
Made by EASYTECH, who also make LightMeter Pro.