How to measure light for plants with your phone: the steps, the white-paper trick, and what to write down
To measure light for plants, put your phone where the leaves are at midday, lay white copy paper flat at that spot, aim the camera at the paper and read lux or foot-candles. Hold still for a few seconds, take three readings, keep the middle one, and write it down with the time and weather.
Every plant care guide says "bright indirect light" and leaves you to guess. A phone turns the guess into a number. It takes two minutes per spot, and the first time you do it you will probably move at least one plant.
The steps are simple. The details below are what make readings you can trust and compare.
What you need
- An iPhone with a light meter app that shows lux or foot-candles
- One sheet of plain white copy paper (ordinary 80 g/m², 20 to 22 lb)
- A note on your phone or a sheet of paper for the log
Step by step
- Pick the time. Midday on an ordinary day. For a grow light, switch it on 10 to 15 minutes earlier so it warms up.
- Wipe the camera lens. A fingerprint can cost more light than a cloud.
- Go to the plant's spot. Measure where the leaves are, at leaf height, not where you are standing or on the windowsill next to the plant.
- Use the white paper (method below). This is the step most people skip.
- Hold still for 3 to 5 seconds until the number settles.
- Take three readings, moving the phone slightly between them, and keep the middle one.
- Read foot-candles or lux, and compare with your plant's band in the plant light table.
- Write it down (log sheet below).
The white-paper trick
A camera aimed at a plant measures the leaves. Dark green leaves read dim and pale leaves read bright under exactly the same light, which is why so many plant light readings look wrong. Paper fixes that: it gives the camera the same white surface every time, lit by whatever light reaches the spot.
Method A, rear camera on paper (easiest). Lay the sheet flat on the surface where the plant sits, or hold it level at leaf height. Hold the phone above it so the paper fills the frame, without casting your own shadow on it. Read the screen.
Method B, paper over the front camera (closest to a light meter). Switch the app to the front camera. Lay the phone flat at leaf height, screen facing up, and place the paper flat over the front camera with no gap. The phone now reads the light falling on the spot from the whole sky or lamp, the way a light meter does. Lift the paper corner to read the screen.
Either works. What matters is that you pick one method and use it every time, and note which one in your log. Paper changes the absolute number a little, so a reading taken one way is best compared with readings taken the same way.
Keep the paper flat and level, facing up. Angle changes readings a lot: tilting a sensor straight at the sun can read several times higher than the same sensor lying flat. Flat is how published plant light bands are measured.
Lux, foot-candles, PPFD: which number to use
- Foot-candles (fc) are what most houseplant tables use. 1 fc = 10.76 lux.
- Lux is the same measure in metric units.
- PPFD (µmol/m²/s) is the plant-light number growers use for lamps. Multiply lux by 0.0185 for daylight, about 0.0143 for a 4000 K white LED, about 0.017 for 3000 K. Lux to PPFD has the full factor table, and the lux to PPFD calculator does the math.
- DLI is the day's total. PPFD × hours × 0.0036. The DLI calculator does it from a reading and the hours of light.
For houseplants in windows, foot-candles are enough. For grow lights, go to PPFD and DLI.
What to write down
A reading without context is useless next month. Keep a simple log:
| Field | Example |
|---|---|
| Date and time | Nov 18, 12:30 |
| Weather | Bright overcast |
| Spot | Living room, east window, 3 ft back, shelf 2 |
| Method | Paper flat, rear camera |
| Reading | 2,600 lux / 240 fc |
| Light source | Daylight |
| PPFD (if you need it) | about 48 µmol |
| Hours of light | Daylight, about 9 h |
| Plant and how it looks | Monstera, new leaf unfurling, no lean |
Three readings make a habit: the sill, the plant's spot, and the spot you are thinking of moving it to. Write the ratio: "the shelf gets a third of the sill." Ratios hold up even when the weather changes.
Compare spots, seasons and changes
Phones shine at comparisons. Use your log to answer the questions that actually decide where a plant goes:
- Which of two spots is brighter, and by how much? Measure both within a few minutes of each other.
- Did moving the plant help? Measure before and after.
- Is winter costing too much light? Repeat the same reading in December and June.
- Did the grow light fade? Repeat the same canopy reading every few months.
Calibrate once for real numbers
If you want absolute numbers you can put next to published targets with confidence, calibrate your phone once:
- Borrow a lux meter or a friend's quantum sensor for ten minutes.
- Measure the same spot with both, same height, same moment.
- Divide the meter's reading by your phone's reading. That number is your correction factor.
- Multiply future phone readings by it.
A 2017 study found that a single factor like this brought a phone camera to about 12.6 percent error against a reference meter, and that every phone needs its own, even two of the same model. Error was largest below 100 lux, so in very dim spots treat readings as rough and focus on comparisons.
No meter to borrow? A grow light that publishes its PPFD at a stated height works too: hang it at that height, measure, and compare with the maker's number.
Common mistakes
- Aiming the camera at the leaves instead of the spot.
- Measuring at the window when the plant sits six feet back.
- One reading on one day. A west window can be dim all morning and blazing at 3 pm.
- Your own shadow on the paper.
- Room lights on while measuring daylight or a grow light; they add light the plant does not get all day.
- A phone case edge creeping over the lens.
Next: use your numbers to check whether your window is bright enough, or see whether you need a PPFD meter for a grow tent.
Questions people ask
Can I use my phone as a light meter for plants?
Yes. A phone camera reading is an estimate, and it is good at what plants need most: telling you which spot is brighter, by how much, and whether a spot falls in the low, medium or bright band. Use the same method every time, and calibrate once against a real meter if you want tighter absolute numbers.
Should I point the phone at the plant or the light?
At the light, never at the plant. A camera aimed at leaves reads their color: dark leaves read dim and pale leaves read bright under the same light. Measure the spot where the plant sits, using white paper laid flat at leaf height, or with the paper over the front camera.
What time of day should I measure plant light?
Midday on an ordinary day gives a reading you can compare with published bands. If a window gets sun in the morning or afternoon, measure then too, because a single noon reading can miss an hour of strong sun. Note the weather each time.
Why does my light meter app give a different number than my friend's?
Every phone camera and app is tuned a little differently, and method changes the number: the angle, the paper, a case edge over the lens. Readings from one phone with one method compare well with each other. Compare across phones only after each is calibrated.
Sources
- Light for Houseplants (UF/IFAS Gardening Solutions) Phone apps estimate light levels and are useful for spotting changes; foot-candle bands to compare against.
- Calculating and Using Daily Light Integral, SPES-720 (Virginia Tech Extension) Phone apps are typically the most cost-effective way to measure; measuring in your own location gives the best information.
- Smartphones as a Light Measurement Tool: Case of Study (Gutierrez Martinez et al., Applied Sciences 2017) One calibration factor brought a phone camera to about 12.6 percent error; error is largest below 100 lux; calibrate per device.
- HO-238: Measuring Daily Light Integral in a Greenhouse (Purdue Extension) Keep sensors level and clean; converting foot-candles to PPFD and DLI.
Made by EASYTECH, who also make LightMeter Pro.