Is a phone light meter accurate? What four lab tests and photographers' checks found, and how to calibrate yours

For photography, yes, once checked. Side-by-side tests put recent iPhone light meter apps within about a third of a stop of a handheld meter in even light, while unchecked phones ran 2/3 to 2 stops off. For lux, lab tests found errors up to 113%. Check your phone once against a known reading and keep the offset.

The short answer

For taking photos, a phone light meter is accurate enough once you have checked it against a known reading. Photography counts light in stops, and a third of a stop is the margin most film and digital shooters work within. Recent phones land there in even light.

For measuring lux, the bar is higher. Lighting standards and lab work need a few percent, and phones are further off than that. They are still useful for comparing places and lamps, because a phone tends to be wrong in the same way each time in the same light.

What you can do today: on a clear day around noon, meter a grey card or a patch of green grass in full sun. At ISO 100 it should read close to EV 15, the sunny 16 value. If your phone says 14 or 16, you have just found your offset.

What the tests found

TestWhat was testedWhat it found
DIAL accredited lab, published 20227 phones, 7 apps, halogen, compact fluorescent and LED at 100, 500 and 1,000 luxWorst error 113% (1,063 lux shown at 500). One phone was 3% off at 500 lux and 89% low at 100 lux. Apps disagreed by up to 358%
University of Maribor, 20229 phones against a reference meterUnder 4,000 K LED, an iPhone 11 Pro Max stayed within -7 to +8%. One Android read about double at every level. Errors were steady per phone in one light but changed under sun and mixed light. Five apps on the same iPhone: 136 to 400 lux
University of Alcalá, 2017Android phones, camera and light sensor, against a calibrated meterCamera method: about 12.6% error after one calibration factor, 6.35% with three ranges. Below 100 lux, uncalibrated errors of 46 to 62%
Warsaw University of Technology, 2024Three high-end phone cameras, raw files, photometric labAt least about 17% error for luminance, from the camera's colour response
Photographers' side-by-side checksPhone apps against handheld and spot meters on the same sceneA recent iPhone within about a third of a stop; an older iPhone a full stop off; one iPhone 2/3 EV under and one Android 2 EV over on the same grey card

Why 113% sounds worse than it is for photos

Photographers and lighting engineers read the same tests differently, because a stop is a doubling.

  • 1/3 stop is 26% more or less light.
  • 1 stop is 100% more, or half.
  • 113% high is just over one stop.

A lux reading 113% high is useless for checking an office against a standard. The same error on a roll of colour negative film is a frame that prints fine. A phone checked once, and off by a third of a stop, is well inside what film and raw files absorb.

Why phones drift

  • iPhone apps read through the camera. They use the camera's own exposure, so they behave like a reflected meter: a white wall reads brighter than a grey card in the same light. See incident vs reflected metering.
  • Most Android lux apps read the ambient light sensor behind the screen, built to dim the display, and its response varies by model.
  • No cosine diffuser. A lab meter's flat white dome weighs light by angle. A bare camera lens does not.
  • Colour response. Camera sensors do not see colours exactly as the eye does, so the error changes between sunlight, LED and tungsten.
  • Low light. Errors are largest below about 100 lux, in every study that measured it.

How to check and calibrate your phone in ten minutes

You need a reference, an evenly lit target and a notebook. A grey card is ideal; a plain mid-grey wall or green lawn works.

  1. Choose a reference. Best: a handheld meter. Good: a digital camera in manual mode, judging the histogram of a frame-filling grey card. Fair: full midday sun, front-lit, where a grey card should read EV 15 at ISO 100.
  2. Meter the same target. Same light, same ISO, the card filling the phone's spot. Hold the phone still for a second before reading.
  3. Write the difference in stops. Phone EV 11.3, reference EV 12: the phone reads 2/3 stop low.
  4. Repeat at two more levels. A bright window and a dim room. If the offset stays the same, you have one number. If it grows in the dark, note it per level.
  5. Repeat under a second source. Daylight and LED can give different offsets. Keep one per source if they differ.
  6. Apply it. If your app has a compensation setting, enter the offset there. If not, shift the ISO: when the phone's settings overexpose by one stop, set the app's ISO one stop higher than your film, 800 for ISO 400 film. When they underexpose, set it lower.

Recheck when you change phones, and once in a while in a scene you know well.

Getting a steady reading every time

  • Tap a mid-tone, never the sky or a lamp.
  • Hold still for a second; the reading settles as the camera does.
  • Meter in the same light as the subject, at the same spot each time you compare.
  • For a backlit subject, tap the face or a grey card held in front of it.
  • For lux, follow the steps in how to measure lux, and for plants, measure plant light with your phone.

Phone or handheld meter?

Use the phone for negative film, digital, scouting locations, comparing lamps, and every time you would otherwise guess. Use a dedicated incident meter for slide film, strobes, and work where a client needs an exact lux figure on paper. A checked phone is the meter you will actually have with you. The full guide to meter types is in light meter.

Questions people ask

Are iPhone light meter apps accurate?

Accurate enough for photography once you check them. In photographers' side-by-side tests a recent iPhone came within about a third of a stop of handheld meters, while an older iPhone was a full stop off. For lux values, lab tests show wider errors, so treat a phone's lux as an estimate.

Can a phone replace a light meter for film photography?

For most colour and black and white negative film, yes. Negative film tolerates a stop of overexposure, more than a checked phone will be off. For slide film, strobes, or scenes with tight highlights, a dedicated incident meter is still the safer tool. Many film shooters carry the phone and a sunny 16 card.

Why do two light meter apps give different readings?

Each app turns the camera's exposure data into light with its own formula and constant, and some read a small spot while others average the frame. In one lab test, five apps on the same iPhone read between 136 and 400 lux under the same light. Pick one app, check it, and stick with it.

How do I calibrate a phone light meter?

Meter an evenly lit grey card with your phone and with a trusted reference: a handheld meter, a digital camera in manual, or sunny 16 in full midday sun. Note the difference in stops, check it at two or three light levels, and apply it every time, for example by shifting the ISO in the app.

Is a phone accurate enough to measure light for plants?

For comparing spots, yes. Readings stay consistent on the same phone in the same kind of light, so you can see that the shelf gets half the light of the windowsill. For an absolute PPFD figure, expect a margin of 10 to 20 percent on a checked phone and more on an unchecked one, which still places most plants in the right light band.

Sources

Made by EASYTECH, who also make LightMeter Pro.