Do you need a PPFD meter? What it measures, and when a phone lux reading plus a factor does the job

A PPFD meter, or quantum sensor, counts the photons between 400 and 700 nm that plants use, in µmol/m²/s. You need one for red and blue grow lights, mixed light sources and high-value crops near their limits. For houseplants, windows and white LED lamps, a phone lux reading times the right factor gets you close enough.

Growers argue about PPFD meters the way photographers argue about lenses. Some say a phone app is useless; others have grown for years with nothing but a cheap lux meter and a conversion table. Both are right, for different setups.

Here is what a PPFD meter actually does, where it earns its place, and where a phone reading plus the right factor gives you the same decision.

What a PPFD meter measures

A PPFD meter, also sold as a quantum sensor or PAR meter, counts the photons that land on its sensor between 400 and 700 nm, the band plants use for photosynthesis. It reports µmol/m²/s. Each photon counts the same whether it is blue, green or red.

Good sensors add two things a phone lacks:

  • A flat spectral response, so a red photon and a blue photon count equally.
  • A cosine corrector, a white diffuser dome that counts light arriving at an angle correctly.

A lux meter, and a phone camera, weighs light the way your eye does: strongly in green-yellow, weakly in deep red and blue. So lux is a measure of brightness to a human, and PPFD is a measure of food for a plant.

Utah State plant physiologist Bruce Bugbee has told growers that a light meter matters more than a pH meter. The reason is simple: if the light drops by half, growth follows it down, and your eyes will not notice the change. Whichever tool you use, measuring beats eyeballing.

When a phone reading plus a factor is enough

For white light, lux and PPFD move together in a predictable ratio, so a lux reading times the right factor gives a good PPFD estimate:

LightFactor (µmol per lux)
Sunlight0.0185
White LED, 3000 K0.017
White LED, 4000 K0.0143
HPS0.0122 to 0.0130
Fluorescent0.0117 to 0.0135

The full table is in lux to PPFD. With it, a phone handles:

  • Houseplants in windows. Bands are wide; you need to know low, medium or bright.
  • White LED grow lights, strips, bulbs and full-spectrum panels without added red.
  • Setting a lamp height for seedlings, herbs and foliage plants.
  • Comparing spots and heights: which shelf is brighter, what raising the lamp 6 inches did.
  • Spotting fade in an older lamp by repeating the same reading every few months.

Virginia Tech Extension notes that phone apps are typically the most cost-effective way to measure plant light. Treat each reading as a band of about plus or minus 20 percent: write 160 to 240, not 200. That is tight enough for every decision above.

When a PPFD meter pays off

  • Red and blue ("blurple") lamps, or white lamps with extra 660 nm red or far-red diodes. Lux barely sees that light, so no factor works. In one study of lamp spectra, 1,000 lux equaled 13.5 µmol from a white LED and 32 from a red LED.
  • Mixed sources. A 3000 K lamp plus daylight through a window has no single factor.
  • High-value crops pushed near their limits, where 20 percent decides yield and you are running strong lamps.
  • Several tents, rooms or fixtures you want to compare in absolute terms.
  • Detailed canopy maps. Growers map a 3x3 to 5x5 grid and aim for the weakest point to be at least 70 to 80 percent of the average.

Even then, the meter has limits. A 1993 comparison found quantum sensors within 7 percent of a lab spectroradiometer under broad-band light, and off by more than 18 percent under red LEDs.

The budget meter trap

Not every meter labeled "PAR" is a good one, and not every lux meter is accurate either.

  • Lux meters vary widely. In a 2022 lab test, only 9 of 22 lux meters met the standard limit for matching the eye's response, and each needed a different correction depending on the light source.
  • Cheap PAR meters often need correcting. Hobbyist comparisons against reference sensors have found multipliers of 1.3 to 1.8 for some budget units, and poor readings when light comes from an angle.

A budget meter is still useful for comparisons, which is the same job a phone does well. If you are going to buy, buy a sensor that publishes its spectral response and has a cosine corrector.

The middle path: calibrate your phone once

You can get most of the benefit of a meter without owning one.

  1. Borrow a quantum sensor from a grow shop, club or friend for ten minutes.
  2. Measure the same spot under your lamp with the sensor and your phone, same height, same moment.
  3. Divide the sensor's PPFD by your phone's lux. That number is your own factor for that phone under that lamp.
  4. Use it from then on.

A 2017 study found that one calibration factor brought a phone camera to about 12.6 percent error against a reference meter, and that each phone needs its own. No meter to borrow? Hang your grow light at the height where the maker publishes a PPFD value, measure, and use that as your reference.

How to get a reading you can trust

  1. Measure at the canopy, never at the lamp.
  2. Turn off other lights; let the lamp warm up 10 to 15 minutes.
  3. Use a white sheet as the target: flat at canopy height under the rear camera, or laid over the front camera with the phone face up.
  4. Read the center and the edges.
  5. Convert with your lamp's factor using the lux to PPFD calculator, then get the day's total with the DLI calculator.

Details and a log sheet are in measure plant light with your phone. For lamp heights by plant and stage, see how far should a grow light be from plants.

The short version

Your setupWhat to use
Houseplants, windowsPhone, foot-candles or lux
White LED grow light, seedlings, herbsPhone plus the lamp's factor
Red and blue or red-added LEDPPFD meter, or the maker's PPFD chart
Grow light plus strong window lightPPFD meter, or measure each source alone
Multiple tents, crops near their limitsPPFD meter, phone for quick checks

Questions people ask

Can a phone app measure PPFD?

A phone measures lux from its camera, and an app converts that to PPFD with a factor for the light source. Under daylight and white LEDs that estimate lands close to a quantum sensor when the method is consistent. Under red and blue lamps it cannot, because lux misses most of that light.

What is the difference between a PAR meter and a lux meter?

A lux meter weighs light like the human eye, peaking in green and nearly blind to deep red and blue. A PAR or PPFD meter counts every photon from 400 to 700 nm equally, the way plants use them. Under white light you can convert between them; under colored grow lights you cannot.

Are cheap PAR meters accurate?

Many are not. Hobbyist comparisons against reference sensors have found budget units needing correction multipliers of 1.3 to 1.8, and some read poorly when light comes from an angle. A cheap meter is still useful for comparing spots, the same job a phone does.

Do I need a PPFD meter for houseplants?

No. Houseplant light bands are wide (pothos grows from about 100 to 200 foot-candles, a fiddle leaf fig at 400 to 800), so a phone reading in foot-candles or lux tells you which band a spot is in. Save a quantum sensor for grow tents with colored lamps.

Sources

Made by EASYTECH, who also make LightMeter Pro.