DLI calculator: how much light your plants get in a day

DLI equals PPFD times hours times 0.0036, which is what this calculator does. A spot at 200 µmol/m²/s for 14 hours gets about 10 mol/m²/day. Low-light houseplants want 3 to 6, medium-light plants 6 to 10, seedlings 6 to 15, lettuce 12 to 17 and tomatoes 20 to 30.

A single light reading tells you how strong the light is right now. Your plant lives on the total it collects between morning and night. That total is the daily light integral, or DLI, and it explains why a plant two metres from a window starves while one on the sill thrives, even when both spots look bright to you at noon. Type a reading and the hours, and see how much light the spot really delivers.

Calculate your DLI

Start from PPFD if you have it from a lamp chart or a meter. If you measured lux, switch to "I have a lux reading" and pick the light source; the calculator converts with the right factor first. Then pick the kind of plant to compare with.

Daily light integral · mol/m²/day

Lamp on-time, or the hours the spot gets this light.

DLI

7.56mol/m²/day

Below the 12 to 17 band: about 37 % short of the low end.

PPFD for 14.5 mol in 14 h
288 µmol/m²/s
Hours for 14.5 mol at your PPFD
26.9 h

Reaching this band would take 26.9 hours at this light. Move the plant closer to the window or lamp, or add a brighter lamp.

The formula

PPFD is the rain rate, DLI is what ends up in the rain gauge. The formula adds up one second of light at a time:

DLI (mol/m²/day) = PPFD (µmol/m²/s) × hours × 3,600 ÷ 1,000,000, which is the same as PPFD × hours × 0.0036.

SituationPPFDHoursDLI
Shelf two metres from a north window15100.5
East windowsill, morning sun60122.6
Desk lamp grow light over a pothos100124.3
Seedlings under an LED panel2001611.5
Herbs under a strong lamp3001617.3
Tomatoes in a sunny greenhouse6001225.9

The same total can come from very different days. 200 µmol/m²/s for 6 hours and 100 µmol/m²/s for 12 hours both give 4.3 mol/m²/day. A dimmer light on a timer for longer can feed a plant as well as a bright one for a short time, up to the hour limits below.

DLI targets by plant

Plant groupDLI (mol/m²/day)
Low-light houseplants: snake plant, ZZ, pothos, peace lily3 to 6
Medium-light houseplants and foliage plants6 to 10
High-light houseplants, succulents, cacti12 to 16
Seedlings, first weeks6 to 10
Seedlings, a few weeks old10 to 15
Microgreens9 to 12
Lettuce and leafy greens12 to 17
Basil and other herbs15 to 25
Tomatoes, peppers, cucumbers20 to 30

Treat these as the band to aim for. A plant below its band survives for a while on stored energy, grows slowly, stretches toward the light and loses lower leaves. A plant inside the band grows at a steady pace. For the full picture by species, start with how much light plants need.

How to read the result

Below the band. Move the plant closer to the window or lamp first: light falls off fast with distance, so a short move makes a big difference. Then add hours, up to 16. If you would need more than 16 hours to reach the band, the light itself is too weak. The calculator shows both the PPFD and the hours that would put you in the middle of the band.

Inside the band. Keep the spot, the hours and the lamp height. Measure again when the seasons change: the sun sits lower and the days are shorter in winter, so the same window delivers far less light.

Above the band. Plants that grew up in strong light handle more. A plant moved from a dim corner to a bright one needs a week or two to adjust, so raise the light in steps and watch for pale, bleached or crisp leaves.

About hours. Extension guides cap home growing at 16 hours of light a day. Past 18 hours, tomatoes develop leaf injury and lettuce gets more tip burn, and plants that flower by day length need their dark period. Light per hour is the better lever.

Measuring DLI on a windowsill

Window light changes all day, so one reading at noon overstates the day. For a quick estimate, take three readings at the same spot: mid-morning, noon and mid-afternoon. Average them, convert to PPFD with the sunlight factor, and multiply by the hours of daylight. For a grow light on a timer, one reading at leaf height is enough, because the light stays the same from on to off.

What is DLI covers the idea in more depth, and is my window bright enough for plants shows how fast window light drops with distance.

Questions

How do you calculate DLI from PPFD?

Multiply the PPFD by the number of hours of light, then by 0.0036. The 0.0036 comes from 3,600 seconds in an hour divided by a million micromoles in a mole. 150 µmol/m²/s for 16 hours gives 150 × 16 × 0.0036 = 8.6 mol/m²/day.

What is a good DLI for houseplants?

Most foliage houseplants do well between 6 and 10 mol/m²/day. Low-light plants such as snake plant, ZZ and pothos hold steady at 3 to 6, and succulents, cacti and other high-light plants want 12 to 16.

Can I calculate DLI from lux?

Yes. Convert the lux to PPFD with the factor for your light (0.0185 for sunlight, about 0.015 for a white LED), then multiply by hours and 0.0036. The calculator does both steps when you choose "I have a lux reading". The lux to PPFD calculator has the full factor table.

Is more DLI always better?

No. Each plant has a range where it grows well; above it, extra light adds heat and stress, and shade plants bleach. Past 16 hours a day, most plants gain little, and tomatoes show leaf injury past about 18 hours. Raise the light level before you add hours.

Keep going

Sources

Made by EASYTECH, who also make LightMeter Pro.